请各位英语达人帮忙翻译啊谢谢了~~翻译成英文

2025-02-13 01:28:44

推荐回答（4个）

回答1：

4. 安装与调整
4.1 安装：
环境要求：端面铣床安装在干燥无粉尘、无腐蚀性气体的温度在10～40℃的室内坚硬水泥地面上。
4.1.1 调平：机床到位后用水平仪置于工作台面调整端面铣床底面的四个调整座，直到调整水平不超过0.5/1000的位置，然后锁紧调平螺母。
4.1.2 接地：必须按电器接线图要求接地线，其规格截面积大于2.5mm2的软铜芯和绿黄组合颜色的绝缘线，接地电阻不大于4欧姆。
4.1.3接气：工作气压为0.5～0.8MPa，耗气量100L/min，将气源接在气源处理器的接头上，检查各气路有无漏气现象。
4.2 调整
4.2.1 夹紧缸的调整：首先松开气缸夹持板上的紧固手柄，将气缸调整到一个能够适应加工型材压紧的合适位置，调整好压头，使其不至碰到定位板。
4.2.2 工作台角度的调整，如需铣削有角度型材，可首先松开定位板下的紧固手柄，拨出定位销，然后将定位板调整到（左55°右55°）适合的范围内，将紧固手柄紧固好。
4.2.3 铣削速度的调整气动原理图
可通过调整气缸上的单向节流阀，以达到进给和后退的合适的速度。（可根据型材质量调整速度快慢）
4.2.4 工件铣削深度的调整
工作铣削深度的调整，可通过调整定位块的位置以达到铣削深度的目的。
4.2.5 电动机的纵向行程的调整：电机的纵向调整也就是铣刀铣削工件（型材）位置的调整。可通过调整定向手柄下方的调整螺母来实现，顺时针方向，电机上升，反之，则下降，调整好位置后，将机箱两侧的五角星型手柄锁紧。
4.2.6 喷雾量大小的调整：调节喷雾量的大小可旋转阀门开关，改变喷洒面的大小。
4.2.7 工作台的调整：在铣削时横向进刀是为了达到工件（型材）铣削需要。
5. 使用与操作
4. Installation and adjustment

4.1 installation:

Environmental Requirements: End-milling machine installed in the dry dust-free, non-corrosive gases in the temperature 10 ~ 40 ℃ hard indoor concrete floor surface.

4.1.1 Leveling: Machine Level in place after the work under the table to adjust the bottom end of the four adjustment milling Block until the adjustment of the level of not more than 0.5/1000 position, and then locking nut leveling.

4.1.2 Ground: must be in accordance with the requirements of electrical wiring diagram grounding line is greater than its cross-sectional area of 2.5mm2 specification of the soft copper color to green-yellow combination of insulated wire, grounding resistance not more than 4 ohms.

Coherent 4.1.3: Working pressure of 0.5 ~ 0.8MPa, consumption 100L/min, the gas source then the source of the gas connector on the processor to check whether the gas leak phenomenon.

4.2 adjustment

4.2.1 clamping cylinder adjustment: First release of the fastening plate cylinder gripping the handle, the cylinder was adjusted to a compact profile to adapt to the appropriate processing location, adjusting the pressure head, so that it does not to touch to the positioning plate.

4.2.2 table angle adjustment for angle milling profiles, be the first release of the fastening plate positioning handle pin set aside, and then adjust the positioning plate to (left 55 ° right 55 °) for the the scope will be good fastening fastening handle.

4.2.3 Milling adjust the speed of pneumatic schematic

Cylinder can be adjusted on a one-way throttle valve in order to achieve back-feed and the appropriate speed. (Which can be adjusted in accordance with the quality of speed profiles)

4.2.4 Milling depth adjustment of the workpiece

Milling depth adjustment work can be targeted by adjusting the location of block in order to achieve the purpose of milling depth.

4.2.5 motors to adjust the vertical journey: the vertical adjustment of motor is the milling cutter workpiece (Profile) position adjustment. May be directed by adjusting the adjusting nut under the handle to achieve, a clockwise direction, the electrical rise, on the contrary, there was a decrease, adjusting the location of a good will on both sides of the five-pointed star-type chassis locking handle.

4.2.6 the size of the adjustment of spray volume: adjust the size of the volume of spray valve can rotate to change the size of sprayed surface.

4.2.7 table adjustment: when in the horizontal feed milling in order to achieve the workpiece (profile) milling needs.

5. The use and operation of

回答2：

http://translate.google.com/translate_t

回答3：

4. Installation and adjustment
4.1 installation:
Environmental Requirements: End-milling machine installed in the dry dust-free, non-corrosive gases in the temperature 10 ~ 40 ℃ hard indoor concrete floor surface.
4.1.1 Leveling: Machine Level in place after the work under the table to adjust the bottom end of the four adjustment milling Block until the adjustment of the level of not more than 0.5/1000 position, and then locking nut leveling.
4.1.2 Ground: must be in accordance with the requirements of electrical wiring diagram grounding line is greater than its cross-sectional area of 2.5mm2 specification of the soft copper color to green-yellow combination of insulated wire, grounding resistance not more than 4 ohms.
Coherent 4.1.3: Working pressure of 0.5 ~ 0.8MPa, consumption 100L/min, the gas source then the source of the gas connector on the processor to check whether the gas leak phenomenon.
4.2 adjustment
4.2.1 clamping cylinder adjustment: First release of the fastening plate cylinder gripping the handle, the cylinder was adjusted to a compact profile to adapt to the appropriate processing location, adjusting the pressure head, so that it does not to touch to the positioning plate.
4.2.2 table angle adjustment for angle milling profiles, be the first release of the fastening plate positioning handle pin set aside, and then adjust the positioning plate to (left 55 ° right 55 °) for the the scope will be good fastening fastening handle.
4.2.3 Milling adjust the speed of pneumatic schematic
Cylinder can be adjusted on a one-way throttle valve in order to achieve back-feed and the appropriate speed. (Which can be adjusted in accordance with the quality of speed profiles)
4.2.4 Milling depth adjustment of the workpiece
Milling depth adjustment work can be targeted by adjusting the location of block in order to achieve the purpose of milling depth.
4.2.5 motors to adjust the vertical journey: the vertical adjustment of motor is the milling cutter workpiece (Profile) position adjustment. May be directed by adjusting the adjusting nut under the handle to achieve, a clockwise direction, the electrical rise, on the contrary, there was a decrease, adjusting the location of a good will on both sides of the five-pointed star-type chassis locking handle.
4.2.6 the size of the adjustment of spray volume: adjust the size of the volume of spray valve can rotate to change the size of sprayed surface.
4.2.7 table adjustment: when in the horizontal feed milling in order to achieve the workpiece (profile) milling needs.
5. The use and operation of

回答4：

这也太难了吧！

最新问答

求助一个可以按镜头，器材型号分类所拍照片的摄影网站

有的人一辈子就学一样技能，有的人是全才，上知天文下知地理，做到最好！怎么好？

请各位英语达人帮忙翻译啊 谢谢了~~翻译成英文

请各位英语达人帮忙翻译啊谢谢了~~翻译成英文